Fix Hard Drive Error code 2000-0142 on Windows computer

If when you run a hard bulldoze diagnostics test on your Dell Windows eleven or Windows ten calculator but receive the Error code 2000-0142, then this postal service is intended to aid y'all. In this mail, nosotros will identify the nigh potential causes to this error, as well as offer the about adequate solutions you lot can endeavour to successfully resolve the consequence.

What does Mistake Code 0142 mean?

If you take encountered the error code 0142 on your Windows xi/10 PC, it's most likely due to a hardware failure. Essentially, the mistake indicates that your PC/laptop has experienced a hard deejay failure and in most cases, yous need to replace the faulty hardware.

When you encounter this mistake, information technology simply means that the hard drive has gone bad or disk failure and requires a replacement.

These failures can be related to corrupted memory, CPU failure, or an disability of your hard drive to pass a cocky-test. The most likely culprits to this error include-

• Faulty or loose SATA connectedness cables to the difficult drive or motherboard.
• Failed Brusque DST.
• Corrupted data on MBR (Primary Boot Record) on the hd.
• Mechanical damage to the hard drive.
• Decadent arrangement files.
• Bad sectors on a hard drive.

Tin you lot gear up a hard drive failure?

Yes, a hard bulldoze failure can be fixed past specially-trained skillful PC hardware technicians. The expert can use a professional information recovery service to repair difficult disks safely and effectively. Simply keep in mind that a repaired hard disk will not perform well enough or last long enough for information technology to be used.

Set up Hard Bulldoze Error lawmaking 2000-0142 on Windows 11/x

If you have encountered this issue, triggered past your hard drive installed on your Dell Windows eleven/10 figurer, you lot tin try our recommended solutions in the lodge presented below to resolve the Difficult Drive Error code 2000-0142 issue.

1. Check for loose or disconnected cables
2. Remove and reinsert the Hard Drive
3. Run CHKDSK
4. Repair Main Boot Record
5. Supplant Hard Bulldoze

Let's have a look at the clarification of the process involved concerning each of the listed solutions.

ane] Cheque for loose or disconnected cables

The start recommended troubleshooting step you tin can take to resolve the Hard Bulldoze Error lawmaking 2000-0142 on your Dell Windows 11/10 PC is to make sure that the SATA cable that connects the hard drive to motherboard is intact. If the cable is connected firmly and not loose simply the error reappears, then it's probable the cable is faulty/bad – replace it with some other working SATA cablevision, and see if it fixes the error. Otherwise, try the next solution.

2] Remove and reinsert the Hard Drive

Y'all may crave the services of a PC hardware technician for this task.

This solution requires you to remove and reinsert the Difficult Drive. To do this, refer to the Service manual for instructions on how to remove and replace the Hard Drive on your Dell Windows system. After reinstalling the hard drive re-run the diagnostics exam with the Dell SupportAssist and see if you receive the aforementioned error code. Visit dell.com to learn more than nigh these tests.

You tin can run the Drive Self Examination (DST) from the Utility Partition also known as the 32 bit diagnostics to make up one's mind if the fault in view is corrected. If the DST (a cursory disk self-test in which your hard disk evaluates its own performance) from the Utility Partition does non signal a drive failure, information technology'southward safe to presume the fault have been corrected and the drive does not demand to exist replaced, considering if your bulldoze is broken or damaged, it will non pass the DST.

3] Run CHKDSK

This solution requires you to run CHKDSK to fix bad sectors on the difficult bulldoze, which can trigger this mistake on your PC.

4] Repair Master Boot Record

Every bit already pointed out, corrupt data on the MBR can cause this mistake to appear on your Dell Windows xi/10 system when you run the diagnostics examination on your hard drive. In this example, y'all can repair the Master Boot Record (MBR) and see if that helps.

5] Replace Hard Drive

Equally a last option, you may need to replace your hard drive and clean install Windows OS. Just before yous do, nosotros recommend you run the SMART test to verify the health of the drive, to be doubly sure the hard drive has failed or deejay failure is imminent.

Brand sure you backup your files. But typically, this error prevents Windows from booting. When this happens, Windows tries to run a system Automatic Startup Repair but fails, throwing your PC into an endless loop. In this case, yous can back upwards your files by removing the hard drive and then inserting it into a USB enclosure and 'slave' the drive to another reckoner, and then backup your data to the computer or another storage device.

Yous can use any of these third-party professional person Backup and Data recovery software for Windows to recover your information from the failed drive. Also, you can recover your files using a Linux Alive USB.

Hope this helps!

Source: https://www.thewindowsclub.com/fix-hard-drive-error-code-2000-0142-on-windows

Posted by: pennystoing.blogspot.com

Share this post